WD200B double clamp digital phase voltammeter is a multi-function meter specially designed for field testing. It has the characteristics of high precision, high stability, low power consumption, and easy use. The AC voltage and AC current can be directly measured without the open circuit of the circuit under test, and the phase between two voltages, two currents, and voltage and current can be measured directly. Phase sequence, transformer wiring group, inductive and capacitive circuits, test the secondary circuit and bus differential protection system, read out the phase relationship between the CTs of each group of differential protection, check whether the wiring of the watt-hour meter is correct or not, overhaul line equipment, etc. The large LCD display of the instrument, with characters up to 40mm, has a backlight, and the display is clear at a glance. Applicable to electric power, petrochemical, metallurgy, railway, meteorology, industrial and mining enterprises, scientific research institutions, measurement departments, etc.
1.Baseline conditions and operating conditions
Reference conditions | Working conditions | |
ambient temperature | 23℃±1℃ | -10℃~40℃ |
environmental humidity | 40%~60% | <80% |
Signal waveform | sine wave β=0.05 | sine wave β=0.05 |
signal frequency | 50HZ±1HZ | 45H~65HZ |
Instrument operating voltage | 9V±0.1V | 9V±1V |
Measure phase current amplitude | 1A±0.1A | 10m~20.0A |
Measure phase voltage amplitude | 100V±10V | 30V~600V |
External electric and magnetic fields | should avoid | |
Measured lead position | The conductor under test is at the approximate geometric center of the jaw |
2. general specification
Features | Phase, AC current, AC voltage, AC leakage current, phase sequence direct test; transformer group, inductive, capacitive circuit discrimination; power factor, power indirect test |
power supply | DC9V alkaline dry battery (1.5V AA×6) |
Power consumption | When the backlight is turned on, the maximum is about 35mA, and the battery works continuously for about 40 hours |
Turn off the backlight, the meter consumes about 5mA, and the battery works continuously for about 300 hours | |
display mode | LCD display, blue screen backlight function, suitable for dark places |
LCD size | 70mm×62mm |
LCD display field | 64mm×54mm |
Meter size | Length, width and thickness: 207mm×101mm×45mm |
Jaw size | φ7.5mm×15mm |
sample rate | About 3 times/sec |
range | AC voltage: 0~20V/200V/600V |
AC current: 0~200mA/2A/20A | |
Phase: 0~360° | |
amplitude range of the measured signal e | U1-U2 phase: 30V~600V |
I1-I2 phase: 10mA~20.00A | |
U1-I2 or I1-U2 phase: 10V~600V, 10mA~20.00A | |
data retention | During the test, press hold to hold the data, and the "DH" symbol will be displayed |
Automatic shut-down | After about 15 minutes of power on, the meter automatically shuts down to reduce battery consumption |
Voltage detection | When the battery voltage is lower than 7.2V, the low battery voltage symbol will be displayed to remind you to replace the battery |
Instrument quality | The main unit is about 550g (with battery), the clamp is about 170g×2, and the test wire is about 250g |
Test lead length | 1.5m |
Current clamp wire length | 2m |
Working temperature and humidity | -10℃~40℃; below 80%Rh |
Storage temperature and humidity | -10℃~60℃; below 70%Rh |
input resistance | input impedance of each gear of the test voltage: 2MΩ |
When measuring the phase of U1U2, the voltage input impedance is: 40kΩ | |
Pressure resistance | The 2000V/50Hz sine wave AC voltage between the upper cover of the instrument and the screws of the battery cover lasts for 1 minute |
Insulation | Between the instrument line and the shell, between the two voltage input terminals ≥10MΩ |
range | resolution | Basic error | |
Voltage | 20V | 0.01V | ±(1.2%rdg+2dgt) |
200V | 0.1V | ||
500V | 1V | ||
Current | 200mA | 0.1mA | ±(1.0%rdg+2dgt) |
2A | 1mA | ||
10A | 10mA | ||
Phase | 0~360° | 1° | ±1° |
Email:info@wgdchipot.com
Whatsapp: +86 13657267902
Skype: sallyliao2006
Wechat:sallyliao ( 13657267902)
Tel:+86 13657267902
Address:13 / F, Building 2, Hangang Science and Technology Industrial Park, Jintan Road, Wuhan, Hubei, China.