WD-2134 Cable Identifier is designed for power cable engineers and cable workers to solve technical problems of cable identification. This product is only suitable for on-site identification of cables that have been powered off. It is strictly forbidden to connect this cable identification instrument to running power cables! This instrument consists of transmitter, receiver, flexible current clamp, etc.
1. Working conditions
base condition | going | remarks | |
ambient temperature | 23℃±1℃ | -10℃~40℃ | / |
The environment wet crossing | 40%~60% | <80% | / |
Voltage frequency measured | 50H z ±1H z | 45H z ~70H z | / |
Receiver operating voltage | 7.4V±0.5V | 7.4V±1V | / |
Transmitter operating voltage | 11.1V ±0.5V | 11.1V ±1.5V | / |
External electric field, magnetic field | Should avoid | ||
Position of the cable being measured | The measured cable is in the approximate geometric center of the flexible coil |
2. Transmitter specifications
Function | Generates a pulse-encoded current signal; displays the remaining battery voltage |
power supply | 11.1V large capacity rechargeable lithium battery, full charge works continuously for about 8 hours |
display mode | Large LCD displays the remaining battery voltage in real time |
pulse voltage | 500V |
Pulse current | Maximum of 30A (depending on the circuit resistance size) |
Pulse frequency | One time / second |
Pulse Width | 2ms |
transmit a signal | The bar graph dynamically displays the emission signal |
Test lead length | 3 meters, with crocodile clip, 1 red and black each |
Operating temperature | -10℃~40℃ |
Storage conditions | -20℃ to 50℃, 95%RH, no dew |
Backlight Control | Yes, with white backlights |
size | 320mm ×275mm ×145mm |
LCD size | 128mm×75mm |
LCD display field | 124mm×67mm |
Instrument weight | Transmitter: 2.5kg |
Total weight: 3.3 kg (including receiver) | |
package size | 400mm *245mm *335mm |
battery power | When the battery voltage is below 9.65V, the low voltage is displayed to charge the battery and below 9.5V |
charger | 12.6V, The D C Charger |
charging interface | Round charging interface, DC identification |
Compression | The transmitter is integrated special tool box and can withstand pressure of about 200kg |
Pressure resistance | AC 3700V / rms (before the top and bottom surface of the instrument box) |
Electromagnetic properties | IEC61326(EMC) |
Refer to safety regulations | IEC61010-1 (CAT Ⅲ 300V, CAT IV 150V, Pollution Level 2) |
3. Receiver specifications
Function | Cable identification (identify and decode the pulse current signal); AC voltage measurement |
power supply | 7.4V large capacity rechargeable lithium battery, USB charging interface, full charge of continuous work for about 8 hours |
Rated current | About 180mA max |
display mode | The 3.5-inch real color LCD screen display, the color electronic dial indication |
Cable identification succeeded | Green grating for clockwise dynamic indication |
non-target cable | Red-orange gratings dynamically indicate counterclockwise |
Accept several sizes | Long width 207mm 101mm 45mm |
flexible coil | Approximately 630mm long, and the line diameter is 6 mm or 12.5mm |
Coil inner diameter | φ 200mm |
lead length | Length of flexible coil lead: 2m |
Voltage test lead | 1m long (1 red and black each) |
scope of test | The coil can detect the pulse signal with a circuit resistance of 0 ~ 2 kΩ; when the detection circuit resistance is 2 kΩ, the transmitter battery power is more than 10V |
Voltage range | AC 0.01V ~600V(50H z /60H z ) |
Voltage accuracy | ±1%±1dgt |
Identify the signal | Color gratings dynamically display the signal intensity |
Detection rate | About 1 time / second |
Gain adjustment | Level 6, press the left and right arrow keys to adjust the signal magnification, the pointer in the middle to two-thirds of the electronic dial best |
Backlight Control | Press the upper and lower arrow keys to adjust the LCD backlight brightness |
Automatic shut-down | About 15 minutes after turning on, the instrument is automatically turned down to reduce battery consumption |
battery voltage | When the battery voltage is below 6.5V, the low voltage is displayed to charge the battery |
charger | 9 The V D C Charger |
charging interface | USB USB |
Working temperature and humidity | -10℃ ~40℃; below 80%Rh |
Storage temperature and humidity | -10℃ to 50℃, 95%RH, no dew |
Receiver weight | Receiver: 370g (with battery) |
Current clamp: 172g | |
Insulation | 100M between the instrument line and the sheath housing |
Suitable for safety regulations | IEC61010-1 CAT Ⅲ 600V, IEC61010-031, IEC61326, contamination grade 2 |
Email:info@wgdchipot.com
Whatsapp: +86 13657267902
Skype: sallyliao2006
Wechat:sallyliao ( 13657267902)